汽車英語詞彙
1. 汽車的單詞怎麼寫
car
意思是:n. 汽車;車廂 、n. (Car)人名;(土)賈爾;(法、西)卡爾;(塞)察爾
1、讀音:英[kɑː]、美[kɑr]
2、相關短語:
safety car安全車 ; 安全汽車 ;[礦業]安全礦車 ; 救生吊車
bumper car碰碰車 ; 碰撞用汽車 ; 碰碰汽車 ; 碰撞用
concept car概念車 ; 概念汽車
3、例句:
Youhave whomrepairyourcar.
你想讓誰去修理你的汽車啊?
(1)汽車英語詞彙擴展閱讀:
詞義辨析:
car,bus,truck,lorry,coach,automobile,jeep,carriage,wagon•這些名詞都與「車」有關。
car多指乘坐人的小汽車或轎車。
bus一般指公共汽車或大型客車。
truck與lorry同義,指卡車或貨車,為美國用詞。
lorry與truck同義,指卡車或貨車,用於英國。
coach原義指四輪馬車,現指轎式汽車,長途公共汽車,還可指火車設有卧鋪的車廂。
automobile是汽車的總稱。
jeep吉普車,指一種小型輕便、適合在崎嶇路面或野外使用的車子。
carriage指馬車,兩匹或兩匹以上馬拉的四輪馬車。
wagon指四輪運貨馬車或牛車,也指鐵路的無蓋貨車。
2. 汽車的英語單詞是什麼
car 小汽車
3. 汽車英語詞彙
http://www.scribd.com/doc/2056911/How-Does-Auto-Components-Work-
4. 汽車的英文單詞是什麼
單詞:car
讀音:英 [kɑː(r)]、美 [kɑːr]
意思:小汽車;轎車;火車車廂;(某種類型的)火車車廂
5. 汽車的英文單詞是什麼
請問是什麼汽車?因為各種車的單詞是不一樣的。
如果是籠統地汽車,car和vehicle都可以
6. 關於汽車專業的英語單詞
4S店,是一種以「四位一體」為核心的汽車特許經營模式。包括整車銷售(Sale)、零配件(Sparepart)、售後服務(Service)、信息反饋等(Survey)。
一 1.Cylinder block 氣缸體
2.Cylinder liner 氣缸套
3.Cylinder head 氣缸蓋
4.Cylinder head gasket 氣缸蓋墊
5.Cylinder haad fasteners 氣缸蓋螺栓
6.Cylinder head cover gasket 氣缸蓋罩襯墊
7.Cylinder head cover 氣缸蓋罩
8.Pistons 活塞
9.Piston pin 活塞銷
10.Piston ring set 活塞環組
11.Crankshaft 曲軸
12.Crankshaft bearing 曲軸軸瓦
13.Camshaft 凸輪軸
14.Camshaft sprocket 凸輪軸齒形皮帶輪
15.Camshaft bearings 凸輪軸軸承
16.Tappet 挺桿
17.Push rod 推桿
18.Rocker arm shaft 搖臂軸
19.Hydraulic bucket tappet 液壓挺桿
20.Flywheel 飛輪
21.Core plug 堵塞
22.Seal 密封環(活塞)
23.Engline carrier 發動機架
24.Bonded rubber mounting 橡膠支座
25.Crandcase breather 曲軸箱通風管
26.Heate pipe for crankcase breather housing曲軸箱進氣加熱管
27.Wiring barress for heater pipe 加熱管線束
28.Intermediate plate 中間板
29.Power unit protection 動力總成護板
30.Noise damping pan 隔音板
常用汽車英文縮寫
A/C Air Conditioning 空調
A/T Automatic Transaxle (Transmission) 自動變速器
ABS Anti-lock Brake System 防抱死剎車系統
目前,最新的ABS已發展到第5代,現今的ABS還有多方面的功能,比如:
1、電子牽引系統(ETS) ,。
2、驅動防滑調整裝置(ASR)
3、電子穩定程序(ESP)
4、輔助制動器
二1.Cover 發動機蓋罩
2.Dreve plate for converter變扭器驅動盤
3.Engine speed sender wheel發動機轉速感測器齒輪
4.Driveng shaft bearing驅動軸軸承
5.Sprocket for camshaft凸輪軸齒形皮帶輪
6.Ribbed belt多楔皮帶
7.Belt tension damper皮帶張緊減震器
8.Crankshaft vibration damper曲軸減震器
9.V-belt pulleyV型皮帶輪
10.Ldler roller惰輪
11.Ribbged belt cover多楔皮帶罩
12.Balance shaft 平衡軸
13.Chain for balance shaft平衡軸鏈
14.Chain tensioner鏈張緊器
15.Sprocket鏈齒輪
16.Mub for sender wheel凸輪軸位置感測器輪
17.Toothed belt sprocket injection pump噴油泵齒形皮帶輪
18.Camshaft oil seal foothed elt side凸輪軸油封,齒形皮帶端
19 Camshaft seal凸輪軸油封
20.Toothd belt cover inj.pump噴油泵齒形皮帶罩
21.Toothd belt relay roller齒形皮帶導向輪
22.Intermediate shaft中間軸
23.Intermediate shaft seal中間軸油封
24.Toothed belt齒形皮帶
25.Damper減振器
26.Toothd belt tensioner齒形皮帶張緊器
27.Toothed belt tor 2nd camshaft第二曲軸正時皮帶
28.Timing chain housing cover正時鏈條
29.Chain sprocket 鏈輪
30.Timing chain 正時鏈條
SUV Sports Utility Vehicle運動型多功能車
MPV Multi-Purpose Vehicle,也叫多功能汽車,俗稱「子彈頭」
GT Grand Touring Cars高級旅行車
三1 Valve spring氣門桿油封
2. Valve stem seal氣門彈簧
3.Pressure limiting valve限壓閥
4.Swirl chamber渦流燃燒室
5.Intake valve guide進氣門導管
6.Exhaust valve guide排氣門導管
7.Camshaft adjuster凸輪軸調節器
8.Control housing控制殼體
9.Toothed belt cover 齒形皮帶罩
10.Oil pressure switch 機油壓力開關
11.Oil temperature sender 機油溫度感測器
12.Oil pressure warning control unit機油壓力報警控制單元
13.Oil level sensor 機油標高開裝置
14..Oil filler cap 機油加油口蓋
15.Oil filler neck 機油加油管
16.Dipstick 機油標尺
17.Oil pump 機油泵
18.Mounting bracket 安裝支架
19.Oil pump drive 機油泵驅動鏈條
20.Pressure regulating valve 壓力調節閥
21.Oil filter 機油濾清器
22.Oil cooler 機油冷卻器
23.Sump upper part 油底殼上部件
24.Sump 油底殼
25.Oil sump gasket 油底殼密封墊
26.Oil reservoir 機油貯藏
27.Oil cooler pipe 機油冷卻油管
28.Fanbelt 風扇皮帶
29.Fan wheel 風扇葉輪
30.Electric fan 電動風扇
AB air bag安全氣囊
ABRS Air Bag Restraint System 安全氣囊
AWD all-wheel drive全輪驅動
AWS all-wheel steering全輪轉向
2WD Two-Wheel Drive 兩輪驅動
4WD Four-Wheel Drive 四輪驅動
4WS Four-Wheel Steering 四輪轉向
ATS anti-thief system防盜系統
GPS global positioning system 全球衛星定位系統
MT manual transmission手動變速器
AT automatic transmission 自動變速器
A/M automatic/manual自動/手動
AMT automatic machincal transmission機械式自動變速器 四:
1.Fan series resistor風扇串聯電阻
2.ELectric fan relay風扇繼電器
3.Coolant level sender冷卻液液面高度感測器
4.Fan thermoswitch風扇熱敏開關
5.Cooling fan housing冷卻風扇罩
6.Positioning unit定位裝置
7.Locking ring鎖圈
8.Air ct導風裝置
9.Expansion tank膨脹罐
10.Aux coolant pump輔助冷卻液泵繼電器
11.Aux coolant pump control unit輔助冷卻液泵繼電器
12.Viscous fan coupling粘性風扇耦合器
13.Coolant pump水泵
14.Coolant pump seals水泵密封墊
15.Coolant pump pulley水泵皮帶輪
16.Thermostat housing節溫器殼體
17.Bearing housing with impeller帶水泵葉輪的水泵殼體
18.Thermostat節溫器
19.Coolant hose flange冷卻液軟軟管法蘭
20.Coolant pipe冷卻液管
21.Water hose冷卻液軟管
22.Hose clip冷卻液軟這
23.Radiator散熱器
24.Cap 膨脹罐蓋
25.Fan run-on thermoswitch風扇起動熱敏開關
26.Coolant temperature sender冷卻液溫度感測器
27.Fan run-on relay風扇起動繼電器
28.Hydraulic motor液壓馬達
29.Cap油箱蓋
30.Filler neck燃油箱
ESP electronic stability program電子穩定程序
ETS exhaust-gas-turbo-supercharger 廢氣渦輪增壓器
EFI electronic fuel injection 電子控制燃油噴射
7. 還有什麼汽車和汽車的英文單詞
這分給我吧~~
我理解你,不在多而在對,對吧\(*。*\)
Porsche====保時捷
Ferrari=====法拉利
Mercedes
Benz==梅賽德斯-賓士
Buick===別克
Volkswagen===大眾
Volvo==沃爾沃
Chevrolet===雪佛蘭
Ford====福特
Cadillac=凱迪拉克
Jaguar==捷豹
Landrover=====路虎
8. 求:汽車專業英語詞彙大全 ,越全越好
汽車專業英語
汽車專業英語 汽車專業英語詞彙 汽車專業英語詞彙大全
中文 English
輪椅升降機 wheel chair lift
圖例 legend
工位 station
吊運裝置 overhead hoist
更衣室 restroom
1號廠房工藝布置方案圖 proposal of the Plant I layout
合籠 mate
底盤平移台 chassis shuttle
車輛轉移台 bus transfer
前圍角板 front wall angle cover
後圍側板 rear wall side cover
保險杠 bumper
三類底盤 three type chassis
左側圍應力蒙皮 R/S stretching skin (road side)
中塗 floating coat
拼裝台 collector
切割輪口 wheel -arch cutting
內飾 trim
線束 harness
返工 re-doing
輪罩護板 wheel house
發車前准備 pre-delivery
舉升 hoist
小批量產品 be pilot
2 套 two kits
配電站 power transformer substation
裙板 skirt
發動機托架 engine holding frame
診斷報警系統 diagnosis and alarming system
互換性 interchangeability
縮微圖紙 microfiche files
總裝 final assembly
磷化 phosphating
儀錶板 dash board
切齊 trimming
結構完整性 structure integrity
自動癒合的防腐材料 self-healing corrosion preventative material
長途客車 inter-city bus
改裝廠 refitting factory
遮陽板 sun visor
隨車工具 tool box
鋼化玻璃 toughened grass
異形鋼管 special steel pipe
全天候空調系統 full range A/C
強制通風 ram-air ventilation
停機時間 downtime
無公害柴油 clean diesel
寬敞懸臂式座椅 roomy cantilevered seat
防滑地板 no-skid floor
織物紋里鋁合金 textured aluminum extrution
爬坡能力 grade ability
排水閥 drain valve
除濕器 moisture ejector
怠速時 at idle
琴式驅動橋 banjo type drive axle
通風口 ct
恆溫控制 thermostatic control
平衡水箱 surge tank
變光開關 simmer switch
消音器 muffler
防破壞 vandal resistant
聚碳化透鏡 poly-carbonate len
鍍鋅板 galvanized plate
搭接 lap
亮麗的外表 smart apperance
隱藏式固定 concealed fastening
水窪 ponding
發動機中置式客車 bus with under floor engine
組合式客車車身 molar bus body
薄殼式結構 shell construction
襯墊 pad
空氣導流板 air deflector
擱梁 shelf beam
腰梁 waist rail
梭梁 stabilizing beam
腰帶式安全帶 diagonal safety belt
壓條 trim strip
嵌條 insertion strip
翼板 fender
斜撐 bracing piece
轉向盤回正性試驗 test of steering wheel returnability
轉向盤轉角脈沖試驗 steering wheel impulse input test
轉向盤轉角階躍輸入試驗 steering wheel step input or transient state yaw response test
極限側向加速度試驗 limiting lateral acceleration test
汽車平順性隨機輸入行駛試驗 automobile ride random input running test
汽車平順性單脈沖輸入行駛試驗 automobile ride single pulse input running test
汽車懸掛系統固有頻率與阻尼比的測定試驗 measurement of natural frequency and damping raito of suspension
功率突然變化影響試驗 test of effect of sudden power change
汽車專業英語詞彙大全
收油門後控制試驗 test of control at breakway
橫風穩定性試驗 test of crosswind stability
反沖試驗 kick-back test
輪胎爆破響應時間試驗 test of burst response of tyre
繞過障礙物試驗 obstacle avoidance test
移線試驗 lane change test
J型轉彎試驗 test of J turn
頻率響應時間試驗 frequency response test
瞬態響應時間試驗 transient response test
階路響應時間試驗 step response test
脈沖響應試驗 pulse response test
靜態操舵力試驗 static steering effort test
懸架舉升試驗 jack-up test of suspension
耐翻傾試驗 test of overturning immunity
輪輞錯動試驗 rim slip test
風洞試驗 wind tunnel test
制動穩定性試驗 test of braking stability
最小轉彎直徑試驗 minimum turning diameter test
操舵力試驗 steering effort test
類型 type
發動機 engine
內燃機 intenal combusiton engine
動力機裝置 power unit
汽油機 gasoline engine
汽油噴射式汽油機 gasoline-injection engine
火花點火式發動機 spark ignition engine
壓燃式發動機 compression ignition engine
往復式內燃機 reciprocating internal combustion engine
化油器式發動機 carburetor engine
柴油機 diesel engine
轉子發動機 rotary engine
旋輪線轉子發動機 rotary trochoidal engine
二沖程發動機 two-stroke engine
四沖程發動機 four-stroke engine
直接噴射式柴油機 direct injection engine
間接噴射式柴油機 indirect injection engine
增壓式發動機 supercharged engine
風冷式發動機 air-cooled engine
油冷式發動機 oil-cooled engine
水冷式發動機 water-cooled engine
自然進氣式發動機 naturally aspirated engine
煤氣機 gas engine
液化石油氣發動機 liquified petroleum gas engine
柴油煤氣機 diesel gas engine
多種燃料發動機 multifuel engine
石油發動機 hydrocarbon engine
雙燃料發動機 el fuel engine
熱球式發動機 hot bulb engine
多氣缸發動機 multiple cylinder engine
對置活塞發動機 opposed piston engine
對置氣缸式發動機 opposed-cylinder engine
十字頭型發動機 cross head engine
直列式發動機 in-line engine
星型發動機 radial engine
筒狀活塞發動機 trunk-piston engine
斯特林發動機 stirling engine
套閥式發動機 knight engine
氣孔掃氣式發動機 port-scavenged engine
傾斜式發動機 slant engine
前置式發動機 front-engine
後置式發動機 rear-engine
中置式發動機 central engine
左側發動機 left-hand engine
右側發動機 right-hand engine
短沖程發動機 oversquare engine
長沖程發動機 undersquare engine
等徑程發動機 square engine
頂置凸輪軸發動機 overhead camshaft engine
雙頂置凸輪軸發動機 al overhead camshaft engine
V形發動機 V-engine
頂置氣門發動機 valve in-head engine
側置氣門發動機 side valve engine
無氣門發動機 valveless engine
多氣門發動機 multi-valve engine
卧式發動機 horizontal engine
斜置式發動機 inclined engine
立式發動機 vertical engine
W形發動機 w-engine
I形發動機 I-engine
L形發動機 L-engine
F形發動機 F-engine
性能 performance
二沖程循環 two-stroke cycle
四沖程循環 four-stroke cycle
狄塞爾循環 diesel cycle
奧托循環 otto cycle
混合循環 mixed cycle
定容循環 constant volume cycle
工作循環 working cycle
等壓循環 constant pressure cycle
理想循環 ideal cycle
熱力循環 thermodynamic cycle
沖程 stroke
活塞行程 piston stroke
長行程 long stroke
上行程 up stroke
下行程 down stroke
進氣行程 intake stroke
充氣行程 charging stroke
壓縮行程 compression stroke
爆炸行程 explosion stroke
膨脹行程 expansion stroke
動力行程 power stroke
排氣行程 exhaust stroke
膨脹換氣行程 expansion-exchange stroke
換氣壓縮行程 exchange-compression stroke
汽車專業英語詞彙大全
止點 dead center
上止點 top dead center(upper dead center)
下止點 lower dead center(bottom dead center)
上止點前 budc(before upper dead center)
上止點後 atdc(after top dead cetner)
下止點前 bbdc(before bottom dead center)
下止點後 abdc(after bottom dead center)
缸徑 cylinder bore
缸徑與行程 bore and stroke
空氣室 energy chamber
氣缸余隙容積 cylinder clearance volume
燃燒室容積 combustion chamber volume
氣缸最大容積 maximum cylinder volume
壓縮室 compression chamber
排氣量 displacement
發動機排量 engine displacement
活塞排量 piston swept volume
氣缸容量 cylinder capacity
單室容量 single-chamber capacity
容積法 volumetry
壓縮比 compression ratio
臨界壓縮比 critical compression ratio
膨脹比 expansion ratio
面容比 surface to volume ratio
行程缸徑比 stroke-bore ratio
混合比 mixture ratio
壓縮壓力 compression pressure
制動平均有效壓力 brake mean effective pressure(bmep)
空燃比 air fuel ratio
燃空比 fuel air ratio
燃料當量比 fuel equivalence ratio
扭矩 torque
單缸功率 power per cylinder
升功率 power per liter
升扭矩 torque per liter
升質量 mass per liter
減額功率 derating power
輸出馬力 shaft horsepower
馬力小時,馬力時 horsepower-hour
總馬力 gross horse power
總功率 gross power
凈功率 net power
燃油消耗量 fuel consumption
比燃料消耗率 specific fuel consumption
空氣消耗率 air consumption
機油消耗量 oil consumption
有效馬力 net horse power
額定馬力 rated horse power
馬力重量系數 horsepower-weight factor
制動功率 brake horse power
制動熱效率 brake thermal efficiency
總效率 overall efficiency
排煙極限功率 smoke limiting horsepower
功率曲線 power curve
機械損失 mechanical loss
機械效率 mechanical efficiency
有效熱效率 effective thermal efficiency
充氣系數 volumetric efficiency
過量空氣系數 coefficient of excess air
適應性系數 adaptive coefficient
扭矩適應性系數 coefficient of torque adaptibility
轉速適應性系數 speed adaptive coefficient
強化系數 coefficient of intensification
校正系數 correction factor
換算系數 conversion factor
活塞平均速度 mean piston speed
發動機轉速 engine speed (rotational frequency)
怠速轉速 idling speed
經濟轉速 economic speed
起動轉速 starting speed
最低穩定工作轉速 lowest continuous speed with load
最大扭矩轉速 speed at maximum torque
最高空轉轉速 maximum no load governed speed
調速 speed governing
超速 overspeed
怠速 idling
轉速波動率 speed fluctuation rate
工況 working condition(operating mode)
額定工況 declared working condition
變工況 variable working condition
穩定工況 steady working condition
空載 no-load
全負荷 full load
超負荷 overload
部分負荷 part load
充量(進氣) charge
旋轉方向 direction of rotation
順時針 clockwise
逆時針 counter-clockwise
左轉 left-hand rotation
右轉 right-hand rotation
外徑 major diameter
中徑 pitch diameter
內徑 minor diameter
徑向間隙 radial clearance
發動機性能 engine performance
載入性能 loading performance
起動性能 starting performance
汽車專業英語詞彙大全
加速性能 acceleration performance
動力性能 power performance
排放性能 emission performance
空轉特性 no load characteristics
負荷特性 part throttle characteristics
調速特性 governor control characteristics
萬有特性 mapping characteristics
穩定調速率 steady state speed governing rate
氣缸體和氣缸蓋 cylinder block and head
氣缸體 cylinder block
整體鑄造 cast inblock (cast enblock)
發動機罩 engine bonnet
氣缸體加強筋 engine block stiffening rib
氣缸 cylinder
(轉子機)缸體 stator
缸徑 cylinder bore
氣缸體機架 cylinder block frame
氣缸蓋 cylinder head
配氣機構箱 valve mechanism casing
氣缸體隔片 cylinder spacer
氣缸蓋密封環 cylinder head ring gasket
氣缸蓋墊片 cylinder head gasket
氣缸套 cylinder liner(cylinder sleeve)
乾式缸套 dry cylinder liner
濕式缸套 wet cylinder liner
氣缸水套 water jacket
膨脹塞 expansion plug
防凍塞 freeze plug
氣缸壁 cylinder wall
環脊 ring ridge
排氣口 exhaust port
中間隔板 intermediate bottum
導板 guideway
創成半徑(轉子機) generating radius
缸體寬度(轉子機) operating width
機柱 column
燃燒室 combustion chamber
主燃燒室 main combustion chamber
副燃燒室 subsidiary combustion chamber
預燃室 prechamber
渦流燃燒室` swirl combustion chamber
分開式燃燒室 divided combustion chamber
渦流式燃燒室 turbulence combustion chamber
半球形燃燒室 hemispherical combustion chamber
浴盆形燃燒室 bathtub section combustion chamber
L形燃燒室 L-combustion chamber
楔形燃燒室 wedge-section combustion chamber
開式燃燒室 open combustion chamber
封閉噴射室 closed spray chamber
活塞頂內燃燒室 piston chamber
爆發室 explosion chamber
燃燒室容積比 volume ratio of combustion cahmber
燃燒室口徑比 surface-volume ratio of combustion chamber
通道面積比 area ratio of combustion chamber passage
曲軸箱通氣口 crankcase breather
凸輪軸軸承座 camshaft bearing bush seat
定時齒輪室罩 camshaft drive(gear)cover
曲軸箱檢查孔蓋 crankcase door